Характеристики и описание
General specifications | |
|---|---|
| Switching function | Normally open (NO) |
| Output type | PNP |
| Rated operating distance | 2 mm |
| Installation | flush |
| Output polarity | DC |
| Assured operating distance | 0 ... 1.62 mm |
| Actual operating distance | 1.8 ... 2.2 mm typ. |
| Reduction factor rAl | 0.23 |
| Reduction factor rCu | 0.21 |
| Reduction factor r304 | 0.7 |
Nominal ratings | |
| Operating voltage | 10 ... 30 V |
| Switching frequency | 0 ... 1000 Hz |
| Hysteresis | 1 ... 10 typ. 3 % |
| Reverse polarity protection | reverse polarity protected |
| Short-circuit protection | pulsing |
| Voltage drop | ? 3 V |
| Voltage drop at IL | |
| Operating current | 0 ... 200 mA |
| No-load supply current | ? 11 mA |
| Switching state indicator | LED, yellow |
Approvals and certificates | |
| UL approval | cULus Listed, General Purpose |
| CSA approval | cCSAus Listed, General Purpose |
| CCC approval | CCC approval / marking not required for products rated ?36 V |
Ambient conditions | |
| Ambient temperature | -25 ... 70 °C (-13 ... 158 °F) |
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) |
Mechanical specifications | |
| Connection type | cable PVC , 5 m |
| Core cross-section | 3 x 0.34 |
| Housing material | Stainless steel 1.4305 / AISI 303 |
| Sensing face | PBT |
| Housing diameter | 12 mm |
| Degree of protection | IP67 |
| Cable | |
Equipment protection level Gc (nA) | |
| Certificate of Compliance | PF 15CERT3754 X |
| Special conditions | |
Equipment protection level Dc (tc) | |
| Instruction | Manual electrical apparatus for hazardous areas |
| Device category 3D | for use in hazardous areas with combustible dust |
| Certificate of Compliance | PF 15CERT3774 X |
| CE marking | [*PD-Z02586A*] |
| ATEX marking |  II 3D Ex tc IIIC T80°C Dc The Ex-related marking can also be printed on the enclosed label. |
| Standards | EN 60079-0:2012+A11:2013, EN 60079-31:2014 Protection by enclosure "tc" Some of the information in this instruction manual is more specific than the information provided in the datasheet. |
| General | The corresponding datasheets, declarations of conformity, EC-type examination certificates, certifications, and control drawings, where applicable (see datasheets), form an integral part of this document. These documents can be found at www.pepperl-fuchs.com. The maximum surface temperature of the device was determined without a layer of dust on the apparatus. Some of the information in this instruction manual is more specific than the information provided in the datasheet. |
| Installation, commissioning | Laws and/or regulations and standaИли отправьте нам запрос наtended usage goal must be observed. If the Ex-relevant identification is printed exclusively on the adhesive label provided, this label must be affixed in the immediate vicinity of the sensor! The background surface to which the adhesivelabel is to be applied must be clean and free from grease! The applied label must be durable and remain legible, with due consideration of the possibility of chemical corrosion! |
| Maintenance | No changes can be made to apparatus, |
General specifications
Inductive sensor NCB2-12GM40-E2-3G-3D-5M
Под заказ
Цену уточняйте
Минск ∙
Доставка
Оплата и гарантии